Reupholster A Rocking Chair With Fabric And Nailheads, step by step

Ok I am back with part two of the madness that is Me vs. Rocker. But remember my disclaimer from yesterday’s post that this whole process was much like when aliens took over my body and I made a quilt for Clara, which is to say: I went rogue. I took in all the advice from you folks along with some google pointers and some suggestions from a reupholstering-fiend friend of mine… and simply played it by ear and did what seemed to work as I went along. I mean, it is not a family heirloom, it is a $25 craigslist find. But sufficient chatter, heeeeere we go.

Although there was a sneak peek pic of the nearly-wrapped up product at the end of the last post, we were in fact here when it came to the play-by-play:

No wait, we had wrapped up that seat and were here after redoing the frame:

Finishing the seat upholstery and the frame meant I could no longer avoid the most intimidating part of this project: that opening at the top part of the chair that would have to look wrapped up from both sides. And yes, I was skeered. But after reading through a ton of recommendations on this original how-do-I-do-it post from nine months ago (and chatting to a reupholstering-fiend friend of mine) I opted to use one of the more surprising yet most commonly recommended methods: heavy duty cardboard. Does not that sound like a terrible idea? I know, it sounds fully wrong. Like bad dollhouse furniture that would be uncomfortable and make weird cardboard sounds when you lean back on it. But I guess a lot of upholstery experts use it and my friend had gorgeously redone an whole dining set with double-sided upholstery simply like my rocker using that method. So I went for it. And in the words of Madonna: I am not sorry (it is huuuuman naaaature). It in fact worked out awesomely. Let us get into it, shall we?

First I used four pieces of cardstock to make a template for the opening (to see simply how wide and long it needed to be to cover some of the gross hole-riddled parts of the frame that the original upholstery had once obscured):

Then I placed that template on the back side of the chair to be sure another upholstered panel of that exact size would work nicely in the back (and cover all the rough areas of the frame that are not meant to be seen back there). It worked in the back too, so I laid my handy little cardstock template down on some heavy duty cardboard (leftover from our Ikea file cabinet packaging) and traced the shape of the template onto the cardboard.

Next I cut each cardboard panel out and used more extra-loft batting and fabric, which I secured from behind to upholster it simply like I did to the seat in the first part of this walkthrough. Oh and you will notice I did my best to center the fabric again and pull it pleasant and taut around the back perimeter. This time I simply used one layer of batting underneath it (instead of five like the seat) since people do not sit on the chair back (they simply lean on it). I do not mind all wood rockers like this, so I was not looking for a ton of top-of-your-back plushness anyway. I simply hoped the batting and fabric to give the heavy duty cardboard even more strength and durability. It was in fact surprisingly legit looking when I was done. And since I worried that staples would poke through the front of my fabric from behind as I secured the batting and fabric, I used duct tape to hold it in place from behind instead – simply until I could staple through everything to attach the panel to the chair (which I knew would hold a lot more firmly over time than tape). I do not think anyone would have guessed it was cardboard and duct tape under there from the front. And the strong thing about it was that it was not fully unbendable…

… but once it was stapled (with my regular old staple gun) to the chair about a quarter of an inch from the edge (through the panel and into the frame) it was fully unbendable and appropriately strong.

I do not think a kid could stab an umbrella through it in fact. It is that strong. See, it gets truly pleasant and rigid once the outside is reinforced with all of those staples around the chair’s wooden frame. And it was pleasant that it was not fully rigid (aka: unbendable) before the stapling step because if I used anything more unbendy (like a piece of metal flashing) I worried it would have been truly hard to attach. Why? Well, whatever I chose for the panel had to have some flex so it could follow the slight curve of the frame without buckling or folding. In short: cardboard sounds crazy, but the thick stuff that is reinforced with batting and fabric = smooth and fully professional looking. I do not think anyone could thump their hand against it (hard, it can take it) and guess that it was cardboard. And it is fully comfortable to lean on, rock in, etc.

But simply stapling the panel around the exterior left me with this dilemma: ugly little visible staples around the perimeter. At first I thought I’d find some sort of trim or burlap ribbon to glue over it (they sell upholstery glue meant for adding trim like that) but the more I looked at options, the more I did not like the idea of adding more contrasting fabric or trim. Nothing seemed to go with my base fabric, and I did not want it to look low-cost or peel off due to constant use (we work our furniture hard in this house).

So I did what any novice chair upholstering gal would do, and fully ignored the problem for the time being. Instead I simply moved on to making the second panel for the back (again using the one layer of batting + one layer of taut fabric method to cover the panel – secured from the back with duct tape and then stapled to the chair frame to hold everything in place for the long haul).

Here is a better shot where you can see how the frame curves a bit, so creating a panel that is not too rigid to follow that curve was key.

From afar she was looking miiightly fine (this is in fact the sneak peek pic I included in yesterday’s post)…

… but up close there was still the visible staple issue around the edge of each panel. So I chose after looking at all of my trimming options at JoAnn that perhaps it was a job for nail heads (sold in packs of 24 for $1.50 each). After all I enjoy the vivid detailing they can add to things (our living room ottoman has them going on, and I am totally picking up what it is putting down). So I quite slowly pried out the staples as I brought in nail heads down the line instead (the staples could be easily popped out with a flat head screwdriver, and then I simply used a small hammer to bang in my nail heads, which in short look like heavy duty thumb tacks).

But after a whole bunch of chihuahua-scaring hammering, I stepped back and hated the lumpy bumpy result. They were simply far too ganked up on each other and no matter how hard I tried to hammer them in straight, there was a slight wiggled effect and it simply was not working for me. I had looked for one of those long rows of nail heads that they sell pre-lined-up on a spool (which likely would have been a lot easier) but I could not find them at JoAnn (hence purchasing individual nail heads instead). But it was certainly time to figure something else out. So I chose to try to space my nail heads a little further out (sort of the same distance as my staples) instead of trying to make a long dense line…

It was soooo much better. I could breathe again. If one was slightly higher or lower than another one it was a lot less obvious this way. And it felt more airy and not as on-top-of-itself crowded.

Oh and simply to be clear, I would remove each staple with the flat head screwdriver as I went along and replace it with a nail head. So it would not be smart to remove all of your staples at once or nothing would hold your panel in place on the chair. Moving around the chair and popping one staple out and one nail head in did the trick. And using a small piece of paper or cardboard as a spacer between the nail heads can assist you keep them pleasant and equidistant. Booyah, Dad. I simply used equidistant on the ol’ journal (he’s a math teacher, so that should thrill him to no end).

Oh and see that ruffled cream thing at the bottom of the pic above and below? That is simply a pillow from the sofa because I was banging the chair fairly hard, so I did not want it rubbing against the floor with every hit. Poor pillow. I am glad to say that he made it through. And here is what I had going on after doing three out of four sides of the front panel:

Not bad, right? It was pleasant because it made the whole chair feel kind of special and pricey in a way that I feared glued cording or trim could not. But I am not gonna lie. This is the hardest step by far, physically. You get sweaty and gross from all that extra-hard hammering and it is simply downright tiring. It is also especially frustrating every once in a while when your nail head inexplicably bends as you hammer it in, which means it is rendered fully useless (and results in a bunch of annoying waste in the end). Simply look at this pile of “brokens”:

I even tried to straighten them with a pliers in the hopes of reusing them, but once they are bent they are simply too compromised to go in straight and look right (and frequently simply break entirely). Bummer.

But in the end (after about an hour and a half spent studding the front panel) I enjoyed the look so much that I even brought in studs along the wood trim part under the seat on the sides and front. Simply to add some balance and bring some of that detailing to the bottom of the rocker along with the top panels. It is hard to tell in the pics, but the studding on the upper panel of upholstery is pleasant and shiny, so adding some shine along the wooden bottom edge of the chair made it feel more not-top-heavy, so it is more balanced looking in person.

Secret: I have not nail-headed the back panel yet, so I have a bit more hammering to do. Perhaps next week when my arms recover. Hah. For now I will simply keep my chair facing forward and nobody will be the wiser. Except for the fact that I simply told everyone. Because I am smooth like that.

Either way, from the front and the side… I think I am in love:

Is not she sexy? Wait, I mean he. The studs and the curves give me mixed signals. Speaking of the studs, for some reason the nail head row on the bottom (that wraps around the wood rail under the seat) reads as a little “medieval” in these pics, but I promise it is not at all reminiscent of Knights Of The Round Table in person, I think the camera simply caught them differently than they read in real life.

But back to those nail heads, my advice to you would be this: buy waaaaay more boxes of nail heads than you think you will need. They are only $1.50 a box (at least at our JoAnn) and you can consistently use coupons on top of that. It is simply waaay more annoying to run out of them and have to treck back out to the store all sweaty and frustrated than to have extra boxes that you can return at the end if you do not need them. To give you an idea of how many boxes I went through, I in fact needed five of them (due to all the annoying bent ones that messed with my mojo). I likely could have done it in three if none of them inexplicably bent on me.

To celebrate fiiiinally finishing (well being 95% done, since I still have to stud the back panel) I chose to have a pillow fashion show. Because I am weird like that. Here is Mr Dapper himself, rocking (har-har) a random green HomeGoods pillow that I have in my embarrassingly extensive pillow collection:

And here he is with a little Anthropologie-ish spin thanks to a lively patterned yellow pillow going on (originally from Target, borrowed from the guest room):

Today he’s “wearing” the little green pillow in the corner of our bedroom, but the patterned yellow one was lively for a hot minute too. We are thinking our rocker might eventually end up in the office, which would be truly pleasant since we spend plenty of Clara-reading time in there (and chose our big green sofa does not truly work with the floor plan that we are working towards). We will certainly share some pics when we pin down a permanent home for the guy.

And simply for kicks, here is a look back at our $25 craigslist rocker before I worked up the took-nine-months-to-cultivate energy to get ‘er done. Ah memories.

You’ve come a long way Rocky. Here is the budget breakdown:

• Rocker (from craigslist): $25
• Extra-loft batting (from JoAnn): $6 (with 50% off coupon)
• Staple gun: $0 (already owned – but it’ll run you $19-ish bucks from Home Depot if you need one)
• Oil-rubbed bronze spray paint (from Home Depot): $7
• Heavy duty cardboard: $0 (leftover from our Ikea file cabinet packaging)
• Kravet fabric (found as a clearance remnant at JoAnn): $4 (for two yards)
• Nail heads (from JoAnn): $6 (they were $1.50 a box & I needed 5 boxes, but used 2 coupons)
• Total: $48

Possibly the most exciting thing? We simply learned that Ballard Designs is selling the same exact Kravet fabric that we found as a clearance remnant at JoAnn for $4 (for two yards) for a whopping $32 a yard (which adds up to $64 for two)! So the fabric that we used on our project alone could have cost more than our whole $48 rocker makeover. Certainly makes the whole roller-coaster upholstery adventure feel like time and money well spent. Although I am still mad that some of my nail heads bent so I had to buy a few extra packs. Oh well, there is no crying in baseball upholstery.

So there you have it. A what-worked-for-me rundown with 44 photos between the this post and part one (hence the two part split). As for how it feels to rock in that guy, in a word: niiiiiice. It is all quite comfy and smooth (with pleasant rock-ability going on). And best of all, there is not an inkling of “is this thing made of cardboard?”- for which I am eternally grateful. Has anyone else out there tried the cardboard panel trick for chair backing (or some other upholstery task)? Is anyone bravely embarking on an even more involved chair makeover (the idea of a wingback makes me shake in my boots)? Good luck and godspeed!

Psst- We announced this weeks giveaway winners. Click here to see if you are one of them.